Design of Feedback Shift Register of Against Power Analysis Attack

Stream ciphers based on linear feedback shift register (LFSR) are suitable for constrained environments, such as satellite communications, radio frequency identification devices tag, sensor networks and Internet of Things, due to its simple hardware structures, high speed encryption and lower power consumption. LFSR, as a cryptographic primitive, has been used to generate a maximum period sequence. Because the switching of the status bits is regular, the power consumption of the LFSR is correlated in a linear way. As a result, the power consumption characteristics of stream cipher based on LFSR are vulnerable to leaking initialization vectors under the power attacks. In this paper, a new design of LFSR against power attacks is proposed. The power consumption characteristics of LFSR can be masked by using an additional LFSR and confused by adding a new filter Boolean function and a flip-flop. The design method has been implemented easily by circuits in this new design in comparison with the others.     

废脱硫剂在铁矿烧结中的应用

钢厂煤气脱硫工序排放的废脱硫剂是一种难以利用的有害固体废弃物，含一定量的铁及较高的钙和硫等元素。对废脱硫剂配入铁矿粉中进行了烧结杯的试验研究，结果表明，当废脱硫剂配比超过01%后，随着废脱硫剂配比的升高，烧结矿转鼓强度下降，利用系数下降，烧结烟气中SO2与NOx浓度增加，烧结矿的还原度有所下降，但烧结矿的低温还原粉化性能有所改善。烧结矿的矿相研究发现，废脱硫剂配比偏大时，磁铁矿体积分数增大，铁酸钙体积分数减少，并由针状结构向柱状、板状演变，烧结矿的气孔率上升。主要原因在于其粒度偏粗，含硫高，不利于成矿。当废脱硫剂粒度为-63mm及其配比控制在01%时，烧结矿的产量和质量有所改善，烟气中SO2、NOx较基准试验变化不大。工业试验表明，在烧结混匀矿中配入废脱硫剂配比小于012%时，烧结矿产量和质量没有明显变化，烧结烟气脱硫脱硝效果也没有受到影响。废脱硫剂掺入铁矿中进行烧结是一种资源化利用的有效方法，不仅解决了有害固体废弃物对环境的影响，而且使二次资源得到综合利用。     

选区激光熔化工艺参数对气雾化316L不锈钢粉末成形制品性能的影响

本研究系统考察了激光功率和扫描速度对316L不锈钢粉末选区激光熔化工艺成形熔道、制品微观组织及力学性能的影响,并分析了各类缺陷的形成原因。研究结果表明:在低激光功率和高扫描速度条件下,熔道中出现了大量球状颗粒,这些颗粒之间的空隙恶化了下一层粉末的熔化条件,这正是成形制品中熔道分布混乱以及孔洞、裂纹产生的根本原因,进而导致成形制品力学性能降低;在高激光功率和低扫描速度条件下,熔池快速升温/冷却的热应力作用增强,使得成形制品的熔道交界处也存在孔洞和裂纹等缺陷。在本研究实验条件下,激光功率为350 W,扫描速度为1750 mm/s时,SLM成形制品的力学性能最为优异,其中抗拉强度为731 MPa、屈服强度为638 MPa、断后伸长率为40.0%,致密度为96.27%。     

Spillover effects of distribution grid tariffs in the internal electricity market: An argument for harmonization?

In many countries, distribution grid tariffs are being reformed to adapt to the new realities of an electricity system with distributed energy resources. In Europe, legislative proposals have been made to harmonize these reforms across country borders. Many stakeholders have argued that distribution tariffs are a local affair, while the European institutions argued that there can be spillovers to other countries, which could justify a more harmonized approach. In this paper, we quantify these spillovers in a simplified numerical example to give insight and an order of magnitude. We look at different scenarios, and find that the spillovers can be both negative and positive. To be able to quantify these effects, we developed a long-run market equilibrium model that captures the wholesale market effects of distribution grid tariffs. The problem is formulated as a non-cooperative game involving consumers, generating companies and distribution system operators in a stylized electricity market.     

车辆自组织网络中新型NP-CSMA随机多址协议研究分析

智能交通的出现使得车辆自组织网络受到越来越多的关注。车辆自组织网络的动态拓扑结构变化非常剧烈,这对网络的吞吐率、传输速率等性能提出了很高的要求。提出1种具有握手机制协议的自适应多通道双时钟NP-CSMA随机多址接入协议。该协议首先区分2种P-CSMA协议,握手机制成功解决了隐藏的终端问题,双时钟机制减少了平均空闲时间,多通道机制增加通道数量和划分用户优先级的同时提高了系统吞吐率,自适应机制能够使系统在高负载下保持稳定吞吐率。还对该协议的传输速率进行了分析,得出该协议的传输速率相对较高的结论。通过平均周期方法推导吞吐率和传输速率的计算公式,仿真结果与理论推导一致。     

基于改进雷达图的配电系统电能质量评估方法

本文针对配电系统电能质量综合评估存在的评估指标权重分配过于主观或客观的问题,提出一种基于改进雷达图法的配电系统电能质量评估方法。该方法利用最小偏差组合权重法计算各评估指标的最优组合权重。并在传统雷达图的基础上对各指标轴间夹角值的确定和特征向量的选取两方面做了进一步的改进。首先采用扇形区域取代原始的三角形区域,并利用最小偏差组合权重法计算各指标轴间夹角值。其次选择新的特征向量构造评估函数对配电系统电能质量进行综合评估。最后通过对某钢铁厂棒材变电站10kV配电系统电能质量进行综合评估,验证了该方法的可行性和合理性。较传统雷达图而言,改进雷达图法解决了传统雷达图法中各指标间信息共用以及评估结果不唯一的问题,使评估结果更加准确合理。     

Stabilizing temperature-capacitance dependence of (Sr,Pb, Bi)TiO3-Bi4Ti3O12 solutions for energy storage

(1-x)Sr_0.7Pb_0.15Bi_0.1TiO₃-xBi₄Ti₃O₁₂ ((1-x)SPBT-xBIT, x = 0-0.125) bulk ceramics were developed and calcined via the solid-state method, aimed at the application of pulsed power capacitors. The phase structures, temperature stability, hysteresis loop, and discharge properties were systematically investigated. Considering both the temperature stability and dielectric properties, 0.925SPBT-0.075BIT bulk ceramics with a capacitance variation satisfying the X7R specification were developed for pulsed power capacitors. The energy storage density was 0.252 J/cm³, and the ceramics showed high temperature stability at 80 kV/cm. The discharge current waveforms of the 0.925SPBT-0.075BIT ceramics were recorded. A high discharge power density of approximately 1.01 × 10⁸ W/kg with an 8 Ω load resistor and short discharge period of 84 ns were achieved at 50 kV/cm. The good temperature stability properties and high power density show that the 0.925SPBT-0.075BIT ceramics are well suited for pulsed power capacitors with a wide temperature range.     

Challenges and new methods for designing reliability experiments

Abstract

Engineers use reliability experiments to determine the factors that drive product reliability, build robust products, and predict reliability under use conditions. This article uses recent testing of a howitzer to illustrate the challenges in designing reliability experiments for complex, repairable systems. We review research in complex system reliability models, failure-time experiments, and experimental design principles. We highlight the need for reliability experiments that account for various intended uses and environments. We leverage lessons learned from current research and propose methods for designing an experiment for a complex, repairable system.     

组合轮径差对地铁车辆动力学性能的影响

为了研究各种轮径差组合形式对地铁车辆动力学性能的影响,基于车辆系统动力学和赫兹非线性接触理论,建立地铁动车非线性动力学模型,分析各种轮径差组合工况下地铁车辆的临界速度、平稳性、安全性和磨耗功率及其变化规律。结果表明:在多种轮径差组合工况下,轮径差增大会使地铁车辆的临界速度有较大幅度降低,会使地铁车辆的横向平稳性和磨耗功率明显增大;轮径差对地铁车辆的垂向平稳性、轮轴横向力、轮轨垂向力、脱轨系数和轮重减载率影响较小;通过左、右曲线时,轮径差对磨耗功率增幅的影响存在差异,但变化规律一致。     

Drag Power Loss Investigation in Cylindrical Roller Bearings Using CFD Approach

In high-speed rolling element bearings, the drag forces can be prominent and it is demonstrated in this investigation that the classical models may not be appropriate for correctly estimating this power loss contribution. A modification of the models is thus proposed, including the usual drag forces formulation relying upon the drag coefficient to be evaluated from a numerical computational fluid dynamics (CFD) approach. A three-dimensional approach that considers both the rings and the cylinder ends seems the only adequate approach to be used because a two-dimensional approach predicts a drag coefficient value that is too low. When using the former computed drag coefficient for the evaluation of the total power losses, high values of oil volume fraction must be employed to recover the measured power losses.